亚洲 欧美 国产在线视频

  • <li id="4tey9"></li>

  • <th id="4tey9"></th>
    1. <rp id="4tey9"></rp><dd id="4tey9"><track id="4tey9"></track></dd>
      減速機附件

      手冊下載

      在線手冊

      網站熱門關鍵字

      減速機附件
      您現在的位置:首頁 ? 手冊下載 ? 減速機附件
      格魯夫減速機使用說明書

      格魯夫減速機使用說明書

      軟件大?。?M
      支持平臺:Windows/Linux/Unlix
      文件格式:RAR
      文件版權:格魯夫機械
      授權方式:免費下載
      開始下載
      下載描述
      安裝要求  
            1、底座式安裝,應校準中心線標高,聯軸器聯接時,應校準兩軸的同
      軸度,柔性聯軸器聯接時浮動量不超過聯軸器的允許范圍,剛性聯接時須保
      證各安裝聯接形位公差。
             2、法蘭式安裝,止口應配合良好,法蘭式安裝并配空心軸聯接時,特
             3、扭力臂安裝,主動的空心軸與被動軸應配合良好,被動軸的浮動
      設備振動應小于彈性塊允許的范圍,力臂應固定并鎖緊。
             4、輸出軸加裝聯軸器、皮帶輪、齒輪、鏈輪等件時,請勿重擊,應用
      輸出外端螺孔,壓入聯接件。皮帶輪、齒輪、鏈輪、攪拌式還需考慮徑向
      力。
             5、空心軸實心軸聯接時(配合公差H7/h6),應涂防銹油。
             6、準備剛性好的基礎或牢固的臺架來安傳動設備,同時也需充分考
      慮即使加上最大載荷也不至于改變裝配好后備部件位置。
             7、安裝升降機時,臺架面上的孔,在滿足絲桿能方便通過的前提下,
      盡可能小。
             8、安裝螺栓一般情況采用8 8級,如果高溫振動沖擊情況,請
      打圓柱銷以免松動。
      1.Choosing foot-mount,the height of center line should be calibrated,
      choosing coupling—connect,coaxiality should be calibrated,choosing flexible
      coupling,run—out should keep within permissible values,choosing rigid
      coupling contour and position tolerance should be guaranteed.choosing
      long coupling.,rigidity of shaft should be enough
        2. Flange—mount,protruding or concave steps should inosculate with
       housings,using hollow shaft.contour and position tolerance at connection
       parts should be guaranteed
        3 .Torque-arm-mount,hollow shafts should be fit with working shafts,
      run out of working shafts and vibration of units should be within ranges of
      vibration values torque arm should be fixed and locked
        4. Installation couplings belt wheels.gears,chain gear on output shafts,
      please use screw hole in shaff end to press them in the correct position(see
      following pictures)and radial force should be considered in case of belt
      wheel Chain gears and agitation mode
        5. When connecting hollow shaft and solid shaft.please clean the
      surface and put anti—corrosive oil on it
        6. Please choose foundation with good rigidity or stable plat form to
      install transmission devices in the meantime.also should take full
      consideration that the positions of all parts will not change even if maximum
      torque is loaded on units
        7. When installing screw Jacks,the screw holes ln mounting plate
      should be as small as possible up to bolts’diameten
        8. Generally fixing bolts adopt GBT8.8 in case of high temperature and
      vibration,please take anti—loose measures The tightening torques of
       binding bolts as follows
      潤滑及密封  
       1、密封性:骨架雙唇油封屬于易損件,由于使用條件的較大差異,骨
      架油封的使用壽命很難確定,失效后須及時更換并補充新油。
             2、潤滑油:減速機一般采用油池飛濺潤滑。對環境溫度高于40'C或減
      速機工作時溫度超過1 00℃時應采用循環油潤滑。油池潤滑的油面高度,規
      定當減速器靜止不運轉時,油面控制在圓油標中心以上的位置。
      *擺線類減速機小機型(x4以下)采用油脂潤滑,建議采用4#二硫化鉬鋰
      基脂,出廠時機內已加滿。中等以上機型(×5以上)采用油浴循環潤滑,
      建議采用50#機械油或90#工業齒輪油,出廠時未加,用戶在開機前應接油
      標注入潤滑油。
      *MB無級變速機必須使用Ub-3牽引液。
      *蝸輪絲桿升降機一般采用3#二硫化鉬鋰基潤滑脂。
          以上所選用的潤滑油可以滿足一般使用要求。若有特殊要求或有經驗的
      用戶,可另行選擇其它牌號的潤滑油。環境溫度低時應降低牌號。
      一般來說,潤滑油牌號由小增大時,對減速機性能有如下影響;
      A、溫度升度,線速度高時程度較明顯;    B、效率降低;
      C、噪聲降低;D、密封性能加強;  E、蝸輪或齒輪承載能力增加。
          3、新機在使用動轉400小時后,應更換一次潤滑油并清理內部油污。
      以后的換油周期在正常情況下為:變速機專用油2000小時;齒輪油8000小
      時。使用環境惡劣或8小時以上連續工作制的場合,應縮短換油時間。
          4、嚴禁不同品質的潤滑油混合使用。因為混合使用時可能發生化學反
      應從而降低或失去潤滑作用
      1 Sealing:The two·lip seal belongs to wearing parts;it's difficult to
      decide the useful time because of the different condition of the use
      condition,affer invalidation,updating new oil timely
        2 Lubrication:generally,gear units should adopt splash lubrication It
      should adopt circulation oil if the ambient temperature above 40℃or
       reducer working temperature above 100℃ The grease surface splash
      lubrication should be above the center of oil scale when the reducer keep
      still
      *R、F、K、T、H、B系列齒輪類減速機的潤滑一般采用中負荷工業齒輪油,
      牌號見表1
      *Genemlly R F K T H B Series gear reducer is adopts the moderate
      lode industrial gear oil.check the oil number on table 1
      *The small type of Cycloid reducer(under X 4)adopt grease lubrication.
      you’d better adopt number 4 molybdenum disulphide grease all machines
      have enough lubrication before leaving factory Above middle type
      (above X 5)adopt lubrication by oil circulation,you’d better adopt number
      50 rnachinery oil or number 90 industry gear oil No oil before leaving
      factory,users have to fill oil before the machine start up
      *MB Speed variator must use UB一3 traction liquid
      *Worm screw Jack must use number 3 molybdenum disulphide grease
        The lubrication,which selected can satisfy the ordinary require If there
      is special require or experienced user can use other oil choose the low
      number oil when the ambient temperature is low
      Generally.the lubrication influence the reducer when the lubrication
      number increasing as the following:
      A When the temperatures increase and linear velocity
      B Efficiency decrease
      C Noise decrease
      D Leak tightness increase
      E Carrying capacity of worm and gear increase
        3 Newmachineworking after 400 hours the oil should be changed and
      removethe deposits and old oil The replace cycle:oilofvariator:2000 hour.
      Gear oil:8000 hour.The vile using environment or over 8 hours continuous
      work—places should shorten the time for oil
        4 Different lubrication using mixed is prohibiting strictly,it may reduce
      the efficiency of the lubrication for the chemical realign

       

      使用養護:  
       1、開機前應檢查機內油面是否符合要求,按提示松開或挽上通氣糟使
      之通氣順暢,并檢查轉動是否靈活。
          2、負載試車前要空載運行半小時左右,確認空載無故障后方可加載運
      行。試車應經常檢查運轉情況:不得有異常沖擊,振動,不得滲、漏油,溫
      升不得超過60℃,最高油溫不得超過100℃(日常工作時也應進行檢查)一
      切正常方可正式工作。
          3、工作中發現異常情況應停機檢查,查明、排除故障后方可繼續工作。
      時常檢查潤滑油情況,注意補足油量,及時更換變質的潤滑油。
          4、若出現安裝方位變動,一般情況下調換油鏡、油塞、通氣帽即可。
          5、減速器應經常保持清潔,外表面不得堆積灰塵、臟物以免影響散熱。
          6、貯存:在干燥通風、室溫環境中存放。當貯存期超過三個月時應作
      防銹處理。放置一年左右的機器,使用時要檢查油封是否老化,油品是否變
      質。
      1 Checking the oil level if it's in line with the require before the machine
      is running,loose or change the vent cap for ventilate unhindered and
      checking the rotating if it's flexible or not
        2 It should be running unloaded half an hours before running loaded,
      checking the running condition on trial fun;no exceptional shock,percussion
       No oil leak The temperature is limited to 60℃ the oil is limited to 100 ℃ (it
      should be checking in routine work as well)it can be running until everything
      is standing by
        3 It must be stopped immediately for check once any problem during
       running gear units,check the condition of the oil fill the oil,change the
      lubrication when it’s deteriorated
        4 If mounting position changed,the position of breathe screw Oil level
      Oil drain plug will be change with each other as usual
        5 Gear units should be keeping clean No dust accumulated on the
      surface in case of influencing radiator
        6 Store it in the environment of dry ventilate and room temperature
      when the storage time exceed 3 months,treat it with rustproof,check 
      the oilclosure and oil whether it had gone bad when the machine is 
      placed for l year
      掃碼向格魯夫尋求幫助
      • 聯系格魯夫
      在線客服
      • 咨詢訂購
        點擊這里給我發消息
      • 技術支持
        點擊這里給我發消息
      • 售后反饋
        點擊這里給我發消息
      • 發票物流
        點擊這里給我發消息
      亚洲 欧美 国产在线视频

    2. <li id="4tey9"></li>

    3. <th id="4tey9"></th>
      1. <rp id="4tey9"></rp><dd id="4tey9"><track id="4tey9"></track></dd>